Proper maintenance of Anderson Manufacturing gear starts with verifying the firearm is unloaded, followed by field stripping, thorough cleaning of the bolt carrier group and barrel, light lubrication of high-friction surfaces, and a final function check. Consistent care prevents carbon buildup and ensures long-term reliability for your AR-15 platform.
This guide is written for new AR-15 owners and general enthusiasts who want a reliable maintenance routine for their Anderson Manufacturing components.
Safety First: Unload and Verify
Before any cleaning begins, point the muzzle in a safe direction. Remove the magazine and lock the bolt carrier group to the rear. Visually and physically inspect the chamber and magazine well to confirm zero live ammunition is present. Keep ammunition stored in a separate room during the cleaning process. This step is non-negotiable for every session.
Field Stripping Your Anderson Rifle
Push the rear takedown pin from left to right until it stops. Pivot the upper receiver away from the lower receiver. Push the front pivot pin to fully separate the upper and lower assemblies. Pull the charging handle and bolt carrier group (BCG) out of the upper receiver. Remove the firing pin retaining pin, then tilt the BCG to slide the firing pin out. Cam the bolt out of the carrier and remove the cam pin. Extract the extractor pin and spring assembly if deep cleaning is required.
Deep Cleaning the Bolt Carrier Group
The BCG is the heart of the action and collects the most carbon. Spray a quality carbon solvent inside the carrier key, on the bolt face, and around the gas rings. Let the solvent dwell for several minutes to break down fouling. Use a bronze brush to scrub the bolt carrier interior and the bolt tail. Scrape carbon off the bolt face and inside the extractor claw with a dedicated scraper tool. Wipe all parts dry with lint-free patches until no black residue remains.
Barrel and Upper Receiver Care
Attach a bore brush to a cleaning rod and run it through the barrel from chamber to muzzle several times. Follow with solvent-soaked patches until they exit clean. Run a dry patch to remove excess liquid. Inspect the crown and gas block alignment for carbon rings. Wipe the upper receiver interior, paying attention to the feed ramps and the area around the barrel extension. Do not oil the bore for storage unless the rifle will sit for months; a dry bore is standard for ready-use firearms.
Lubrication Points and Reassembly
Anderson gear runs best with light, high-temperature grease or oil on specific friction points. Apply a thin coat to the bolt cam pin, the bolt rails, and the interior of the carrier where the bolt rides. Place a single drop on the extractor spring and pin. Lightly coat the charging handle latch contact point. Reassemble the BCG in reverse order. Mate the upper and lower receivers, secure the takedown pins, and cycle the action manually to distribute lubricant.
| Component Area | Lubricant Type | Amount |
|---|---|---|
| Bolt Carrier Rails | Light Grease / CLP | Thin Film |
| Cam Pin & Bolt Lugs | Light Grease | Thin Film |
| Extractor Spring/Pin | Light Oil | One Drop |
| Charging Handle Latch | Light Oil | One Drop |
| Trigger Group (Lower) | Light Oil | Sparse Dabs |
Function Testing and Storage Tips
Perform a standard function check. With the safety on, pull the trigger; the hammer should not fall. Switch safety to fire, pull and hold the trigger, cycle the charging handle, release the trigger; you should hear a distinct click (disconnector reset). Verify the bolt locks back on an empty magazine. Store the rifle in a low-humidity environment. A silicone-treated gun sock or a safe with a dehumidifier rod protects the finish on your Anderson lower and upper receivers.
Frequently Asked Questions
How often should I clean my Anderson AR-15?
Clean your rifle after every range session or every 300 to 500 rounds fired. If the rifle is carried in harsh environments, wipe it down and lubricate critical points weekly regardless of round count.
Can I use WD-40 to clean my Anderson gear?
WD-40 is a water displacer and light solvent, not a long-term lubricant or protectant. Use it only for initial carbon removal, then wipe it completely dry and apply a dedicated gun oil or CLP for lubrication and rust prevention.
What is the most common maintenance mistake with Anderson lowers?
Over-lubricating the lower receiver trigger group attracts grit and causes grit-induced wear. Apply only a microscopic dab of grease on the hammer and trigger pin contact surfaces and a drop of oil on the safety detent spring.
Editorial Disclaimer: This is an independent educational and analytical guide inspired by the subject matter. It is not officially affiliated with, sponsored by, or endorsed by any referenced individuals, entities, or trademark holders.